MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 190


MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 19026253429272840392021211213836351617101811897615145b542313222120225a14a
Item no. Part number Designation/description Quant information
CRANKSHAFT
----- A 621 030 19 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE GLYCO OPTIONAL 		001
----- A 621 030 20 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE LAUCHERTHAL OPTIONAL 		001
1 A 621 030 11 01  CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL 		001
2 A 180 031 00 52  SHIM, 5.45 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 01 52  SHIM, 5.60 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 02 52  SHIM, 5.75 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 03 52  SHIM, 5.90 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 04 52  SHIM, 6.05 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
3 WOODRUFF KEY
ON CRANKSHAFT, FRONT 5 X 7,5 DIN 6888 		001
4 A 180 052 02 03  CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT 		001
5 A 180 031 04 25  OIL SLINGER RING
ON CRANKSHAFT, FRONT 		001
5a A 121 031 03 07  COUNTERWEIGHT 001
5b A 121 031 00 51  SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING 		001
6 CYLINDRICAL PIN
8 H8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
7 CYLINDRICAL PIN
8 H8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
8 A 621 030 03 05  FLYWHEEL WITH 001
9 A 621 032 01 05  STARTER RING 001
10 A 121 031 06 71  NECKED-DOWN BOLT
FOR FLYWHEEL AT CRANKSHAFT 		006
11 CYLINDRICAL PIN
10 H8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT 		001
13 A 186 031 02 71  COLLAR SCREW 001
14 A 120 031 01 81  SEALING RING
AT CRANKSHAFT, FRONT 		001
14a A 121 032 00 15  ADJUSTING NEEDLE
FOR TOP DEAD CENTER ADJUSTMENT 		001
----- A 621 032 00 74  PIN AT CYLINDER CRANKCASE 001
15 A 121 200 01 05  PULLEY
DIA. 122 MM UP TO ENGINE 		001
----- A 621 200 01 05  PULLEY
DIA. 135 MM FROM ENGINE 		001
16 ANNULAR GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT 		001
17 A 186 031 00 33  LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT 		001
18 FABRIC SEALING RING
75 X 87 X 6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR 		001
CRANKSHAFT BEARING
20 A 121 030 05 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE GLYCO) OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 00 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE LAUCHERTHAL) OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 10 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE VANDERVELL) OPTIONAL READY FOR INSTALLATION 		001
21 A 121 033 14 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BE 		004
----- A 621 033 00 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 19 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENT 		004
22 A 121 033 14 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 00 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 19 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 06 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZEI MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 01 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 11 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 15 01  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 01 01  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 20 01  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 15 02  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 01 02  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 20 02  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 07 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 02 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 12 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 16 01  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 02 01  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 21 01  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 16 02  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 02 02  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 21 02  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 08 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM = REPAIR SIZE III MAKE GLYCO READY FOR INSTALLATION 		001
----- A 621 030 03 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE LAUCHERTHAL READY FOR INSTALLATION 		001
----- A 121 030 13 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE VANDERVELL READY FOR INSTALLATION 		001
----- A 121 033 17 01  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 03 01  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 22 01  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 17 02  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 03 02  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 22 02  CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 09 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV, MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 04 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 14 97  SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 18 01  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 04 01  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 23 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 18 02  CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 04 02  CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 23 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
CONNECTING ROD
25 A 621 030 05 20  CONNECTING ROD 004
26 A 621 038 00 50  CONNECTING ROD BUSHING 004
27 A 121 038 03 71  CONNECTING SCREW 008
28 A 182 038 00 72  NUT 008
----- A 621 038 01 50  CONNECTING ROD
BUSHING, EXTERIOR DIA. 29.5-MM REPAIR DESIGN 		004
----- A 121 038 28 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL

Replaced by: A 121 038 28 10
29 A 121 038 28 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL 		008
----- A 121 038 07 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL

Replaced by: A 121 038 07 10
----- A 121 038 07 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 33 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 29 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL

Replaced by: A 121 038 29 10
----- A 121 038 29 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL 		008
----- A 121 038 08 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL

Replaced by: A 121 038 08 10
----- A 121 038 08 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 34 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 30 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL

Replaced by: A 121 038 30 10
----- A 121 038 30 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL 		008
----- A 121 038 09 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL

Replaced by: A 121 038 09 10
----- A 121 038 09 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 35 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II, MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 31 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL

Replaced by: A 121 038 31 10
----- A 121 038 31 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL 		008
----- A 121 038 10 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL

Replaced by: A 121 038 10 10
----- A 121 038 10 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 36 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 32 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL

Replaced by: A 121 038 32 10
----- A 121 038 32 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL 		008
----- A 121 038 11 11  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL

Replaced by: A 121 038 11 10
----- A 121 038 11 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 37 10  CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV, MAKE VANDERVELL OPTIONAL 		008
PISTON
----- A 621 030 10 17  PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD

Replaced by: A 621 030 21 17
34 A 621 030 21 17  PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD 		004
35 A 001 037 79 16  COMPRESSION RING
FOR PISTON GROOVE I 		004
36 A 001 037 84 16  COMPRESSION RING
FOR PISTON GROOVE II AND III 		008
38 A 001 037 74 18  PC-OIL SLOTTED RING
FOR PISTON GROOVE IV 		004
39 A 621 037 00 20  PISTON PIN 004
40 A 000 994 25 35  WIRE SNAP RING 008
----- A 621 030 11 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I

Replaced by: A 621 030 22 17
----- A 621 030 22 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I 		004
----- A 001 037 80 16  COMPRESSION RING
FOR PISTON GROOVE I 		004
----- A 001 037 85 16  COMPRESSION RING
FOR PISTON GROOVE II AND III 		008
----- A 001 037 75 18  PC-OIL SLOTTED RING
FOR PISTON GROOVE IV 		004
----- A 621 037 00 20  PISTON PIN 004
----- A 000 994 25 35  WIRE SNAP RING 008
----- A 621 030 12 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II

Replaced by: A 621 030 23 17
----- A 621 030 23 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II 		004
----- A 001 037 81 16  COMPRESSION RING
FOR PISTON GROOVE I 		004
----- A 001 037 86 16  COMPRESSION RING
FOR PISTON GROOVE II AND III 		008
----- A 001 037 76 18  PC-OIL SLOTTED RING
FOR PISTON GROOVE IV 		004
----- A 621 037 00 20  PISTON PIN 004
----- A 000 994 25 35  WIRE SNAP RING 008
----- A 621 030 13 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III

Replaced by: A 621 030 24 17
----- A 621 030 24 17  PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III 		004
----- A 001 037 82 16  COMPRESSION RING
FOR PISTON GROOVE I 		004
----- A 001 037 87 16  COMPRESSION RING
FOR PISTON GROOVE II AND III 		008
----- A 001 037 77 18  PC-OIL SLOTTED RING
FOR PISTON GROOVE IV 		004
----- A 621 037 00 20  PISTON PIN 004
----- A 000 994 25 35  WIRE SNAP RING 008
----- A 621 030 14 17  PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV

Replaced by: A 621 030 25 17
----- A 621 030 25 17  PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV 		004
----- A 001 037 83 16  COMPRESSION RING
FOR PISTON GROOVE I 		004
----- A 001 037 88 16  COMPRESSION RING
FOR PISTON GROOVE II AND III 		008
----- A 001 037 78 18  PC-OIL SLOTTED RING
FOR PISTON GROOVE IV 		004
----- A 621 037 00 20  PISTON PIN 004
----- A 000 994 25 35  WIRE SNAP RING 008