MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 190


MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 190181716103536373821393425262927282021114a21622212022982457141513
Item no. Part number Designation/description Quant information
CRANKSHAFT
----- A 121 030 37 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE LAUCHERTHAL OPTIONAL 		001
----- A 121 030 39 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE GLYCO OPTIONAL 		001
1 A 121 030 35 01  CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL 		001
2 A 180 031 00 52  SHIM, 5.45 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 01 52  SHIM, 5.60 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 02 52  SHIM, 5.75 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 03 52  SHIM, 5.90 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 04 52  SHIM, 6.05 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- WOODRUFF KEY
5X7,5 DIN 6888 FOR CRANKSHAFT GEAR 		001
4 A 180 052 02 03  CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT 		001
5 A 180 031 04 25  OIL SLINGER RING
ON CRANKSHAFT, FRONT 		001
6 A 121 031 03 07  COUNTERWEIGHT 001
7 A 121 031 00 51  SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING 		001
----- CYLINDR. PIN
8 H8X8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
----- CYLINDR. PIN
8 H8X16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
8 A 121 030 08 05  FLYWHEEL WITH 001
9 A 121 032 00 05  STARTER RING 001
10 A 121 031 06 71  NECKED-DOWN BOLT
FOR FLYWHEEL AT CRANKSHAFT 		006
----- CYLINDR. PIN
10 H8X18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT 		001
13 A 186 031 02 71  COLLAR SCREW 001
14 A 120 031 01 81  SEALING RING
AT CRANKSHAFT, FRONT 		001
14a A 121 032 00 15  ADJUSTING NEEDLE
FOR TOP DEAD CENTER ADJUSTING 		001
----- CYLINDR. SCREW
AM 6X8 DIN 84-4 S FOR FIXING OF ADJUSTING NEEDLE 		001
15 A 121 200 01 05  PULLEY 001
16 GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT 		001
17 A 186 031 00 33  LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT 		001
18 FABRIC SEALING RING
75 X 87 X 6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR 		001
CRANKSHAFT BEARING
20 A 121 030 05 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 70-MM = STANDARD (MAKE GLYCO) OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 00 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 70-MM = STANDARD (MAKE LAUCHERTHAL) OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 10 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 70-MM = STANDARD (MAKE VANDERVELL) OPTIONAL READY FOR INSTALLATION 		001
21 A 121 033 14 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 00 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 19 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
22 A 121 033 14 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 00 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 19 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 06 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 01 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 11 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 15 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 01 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 20 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 15 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 01 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 20 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 07 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 02 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 12 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.50-MM = REPAIR SIZE II MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 16 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 02 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 21 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 16 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 02 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 21 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 08 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MM = REPAIR SIZE III MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 621 030 03 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 13 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.25-MM = REPAIR SIZE III MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 17 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 03 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 22 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 17 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 03 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 22 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 030 09 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 04 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 030 14 97  SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MM = REPAIR SIZE IV MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION 		001
----- A 121 033 18 01  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 04 01  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE 		004
----- A 121 033 23 01  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN 		004
----- A 121 033 18 02  CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 621 033 04 02  CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
----- A 121 033 23 02  CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL 		002
CONNECTING ROD
25 A 121 030 15 20  CONNECTING ROD 004
26 A 186 038 07 50  CONNECTING ROD BUSHING 004
27 A 121 038 03 71  CONNECTING SCREW 008
28 A 182 038 00 72  NUT 008
----- A 186 038 08 50  CONNECTING ROD
BUSHING, OUTER DIA. 28.5 REPAIR DESIGN 		004
29 A 121 038 28 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 52.00 = STANDARD MAKE GLYCO OPTIONAL 		008
----- A 121 038 07 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 52.00 = STANDARD MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 33 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 52.00 = STANDARD MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 29 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.75 = REPAIR SIZE I MAKE GLYCO OPTIONAL 		008
----- A 121 038 08 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.75 = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 34 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.75 = REPAIR SIZE I MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 30 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.50 = REPAIR SIZE II MAKE GLYCO OPTIONAL 		008
----- A 121 038 09 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.50 = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 35 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.50 = REPAIR SIZE II MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 31 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.25 = REPAIR SIZE III MAKE GLYCO OPTIONAL 		008
----- A 121 038 10 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.25 = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 36 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.25 = REPAIR SIZE III MAKE VANDERVELL OPTIONAL 		008
----- A 121 038 32 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.00 = REPAIR SIZE IV MAKE GLYCO OPTIONAL 		008
----- A 121 038 11 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.00 = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL 		008
----- A 121 038 37 10  CONNECTING ROD
BEARING SHELL, INNER DIA. 51.00 = REPAIR SIZE IV MAKE VANDERVELL OPTIONAL 		008
PISTON
34 A 121 030 02 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.00 = STANDARD MAKE MAHLE OPTIONAL 		004
----- A 121 030 08 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.00 = STANDARD MAKE NÜRAL OPTIONAL 		004
35 A 001 037 38 16  COMPRESSION RING
FOR GROOVE I 		004
36 A 001 037 43 16  TAPERED RING
FOR GROOVE II 		004
37 A 000 037 00 17  NOVIX STEPPED RING
FOR GROOVE III 		004
38 A 000 037 29 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
39 PISTON PIN
D 25X18X72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 03 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.25 = REPAIR SIZE I MAKE MAHLE OPTIONAL 		004
----- A 121 030 09 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.25 = REPAIR SIZE I MAKE NÜRAL OPTIONAL 		004
----- A 001 037 39 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 44 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 11 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 69 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 04 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.50 = REPAIR SIZE II MAKE MAHLE OPTIONAL 		004
----- A 121 030 10 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 85.50 = REPAIR SIZE II MAKE NÜRAL OPTIONAL 		004
----- A 001 037 40 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 45 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 01 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 36 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 05 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 86.00 = REPAIR SIZE III MAKE MAHLE OPTIONAL 		004
----- A 121 030 11 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 86.00 = REPAIR SIZE III MAKE NÜRAL OPTIONAL 		004
----- A 001 037 41 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 46 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 02 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 37 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 06 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 86.50 = REPAIR SIZE IV MAKE MAHLE OPTIONAL 		004
----- A 121 030 12 17  PISTON WITH
PISTON PIN AND PISTON RINGS, CYLINDER DIA. 86.50 = REPAIR SIZE IV MAKE NÜRAL OPTIONAL 		004
----- A 001 037 42 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 47 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 03 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 38 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008