MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 190


MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 190222021225a21282720211213837363940262914a101617131567145b54982311353425
Item no. Part number Designation/description Quant information
CRANKSHAFT
----- A 121 030 37 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS LAUCHERTHAL OPTIONAL 		001
----- A 121 030 39 01  CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS GLYCO OPTIONAL 		001
1 A 121 030 35 01  CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL 		001
2 A 180 031 00 52  SHIM 5.45 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 01 52  SHIM 5.60 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 02 52  SHIM 5.75 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 03 52  SHIM 5.90 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
----- A 180 031 04 52  SHIM 6.05 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT 		001
3 WOODRUFF KEY
5X7,5 DIN 6888 		001
4 A 180 052 02 03  CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT 		001
5 A 180 031 04 25  OIL SLINGER RING
ON CRANKSHAFT, FRONT 		001
----- A 121 031 01 07  REPLACED BY
121 031 03 07 TOGETHER WITH 1 SPACER RING 121 031 00 51 UP TO ENGINE 75 11543 WITH EXCEPTION OF 75 11374 TO 75 11423
5a A 121 031 03 07  COUNTERWEIGHT
FROM ENGINE 75 11544 IN ADDITION MOUNTED IN 75 11374 TO 75 11423 		001
5b A 121 031 00 51  SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING FROM ENGINE 75 11544 IN ADDITION MOUNTED IN 75 11374 TO 75 11423 		001
6 CYLINDRICAL PIN
8 H8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
7 CYLINDRICAL PIN
8 H8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT 		001
----- A 121 030 03 05  FLYWHEEL WITH

Replaced by: A 121 030 08 05
8 A 121 030 08 05  FLYWHEEL WITH 001
9 A 121 032 00 05  STARTER RING
GEAR, 108 TEETH 		001
10 A 121 031 06 71  NECKED-DOWN BOLT
FOR FLYWHEEL AT CRANKSHAFT 		006
11 CYLINDRICAL PIN
10 H8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT 		001
----- A 121 206 01 17  WASHER
FOR HUB, PULLEY UP TO ENGINE 6500024 		001
13 A 186 031 02 71  COLLAR SCREW 001
14 A 120 031 01 81  SEALING RING
AT CRANKSHAFT, FRONT 		001
14a A 121 032 00 15  ADJUSTING NEEDLE
FOR TOP DEAD CENTER ADJUSTMENT 		001
----- CYLINDER SCREW
AM 6X8 DIN 84-4 S FOR ADJUSTMENT POINTER - FIXING FROM ENGINE 8509140 		001
----- A 121 206 00 10  PULLEY

Replaced by: A 121 200 01 05
15 A 121 200 01 05  PULLEY 001
16 GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT 		001
17 A 186 031 00 33  LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT 		001
----- A 121 031 00 53  SPACER SLEEVE
IN CRANKSHAFT FOR GROOVED BEARING UP TO ENGINE 6510419 		001
18 FABRIC SEALING RING
75X87X6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR 		001
CRANKSHAFT BEARING
20 A 121 030 05 97  SET OF
CRANKSHAFT BEARING SHELLS, GLYCO INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 030 10 97  SET OF
CRANKSHAFT BEARING SHELLS, VANDERVELL INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL 		001
----- A 621 030 00 97  SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL 		001
21 A 121 033 14 01  CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN 		004
----- A 121 033 19 01  CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 00 01  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER 		004
22 A 121 033 14 02  CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 033 19 02  CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 621 033 00 02  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 030 06 97  SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 030 11 97  SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		001
----- A 621 030 01 97  SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 033 15 01  CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER BEARIN 		004
----- A 121 033 20 01  CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 01 01  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER 		004
----- A 121 033 15 02  CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 033 20 02  CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 621 033 01 02  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 030 07 97  SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 030 12 97  SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL 		001
----- A 621 030 02 97  SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 033 16 01  CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN 		004
----- A 121 033 21 01  CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 02 01  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER 		004
----- A 121 033 16 02  CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 033 21 02  CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 621 033 02 02  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 030 08 97  SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 030 13 97  SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		001
----- A 621 030 03 97  SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 033 17 01  CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN 		004
----- A 121 033 22 01  CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 03 01  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER 		004
----- A 121 033 17 02  CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 033 22 02  CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 621 033 03 02  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 030 09 97  SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 030 14 97  SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		001
----- A 621 030 04 97  SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		001
----- A 121 033 18 01  CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN 		004
----- A 121 033 23 01  CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B 		004
----- A 621 033 04 01  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER 		004
----- A 121 033 18 02  CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 121 033 23 02  CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
----- A 621 033 04 02  CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING 		002
CONNECTING ROD
25 A 121 030 15 20  CONNECTING ROD 004
26 A 186 038 07 50  CONNECTING ROD BUSHING 004
27 A 121 038 03 71  CONNECTING SCREW 008
28 A 182 038 00 72  NUT 008
----- A 186 038 08 50  CONNECTING ROD
BUSHING, EXTERIOR DIA. 28.5-MM REPAIR DESIGN 		004
----- A 121 038 28 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 28 10
29 A 121 038 28 10  CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 07 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 07 10
----- A 121 038 07 10  CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 33 10  CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 29 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 29 10
----- A 121 038 29 10  CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 08 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 08 10
----- A 121 038 08 10  CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 34 10  CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 30 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 30 10
----- A 121 038 30 10  CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 09 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 09 10
----- A 121 038 09 10  CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 35 10  CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 31 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 31 10
----- A 121 038 31 10  CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 10 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 10 10
----- A 121 038 10 10  CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 36 10  CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 32 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 32 10
----- A 121 038 32 10  CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 11 11  CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL

Replaced by: A 121 038 11 10
----- A 121 038 11 10  CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		008
----- A 121 038 37 10  CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL 		008
PISTON
34 A 121 030 02 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA.85.00 MM = STANDARD OPTIONAL 		004
----- A 121 030 08 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA.85.00 MM = STANDARD OPTIONAL 		004
35 A 001 037 38 16  COMPRESSION RING
FOR GROOVE I 		004
36 A 001 037 43 16  TAPERED RING
FOR GROOVE II 		004
37 A 000 037 00 17  NOVIX STEPPED RING
FOR GROOVE III 		004
38 A 000 037 29 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
39 PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
40 WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 03 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 85.25 MM REPAIR SIZE I. OPTIONAL 		004
----- A 121 030 09 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA. 85.25 MM REPAIR SIZE I. OPTIONAL 		004
----- A 001 037 39 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 44 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 11 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 69 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 04 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 85.50 MM = REPAIR SIZE II. OPTIONAL 		004
----- A 121 030 10 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA. 85.50 MM = REPAIR SIZE II. OPTIONAL 		004
----- A 001 037 40 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 45 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 01 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 36 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 05 17  PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE MAHLE FOR CYLINDER DIA. 86.00 MM = REPAIR SIZE III. OPTIONAL 		004
----- A 121 030 11 17  PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE NÜRAL FOR CYLINDER DIA. 86.00 MM = REPAIR SIZE III. OPTIONAL 		004
----- A 001 037 41 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 46 16  COMPRESSION RING
FOR GROOVE II 		004
----- A 000 037 02 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 37 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008
----- A 121 030 06 17  PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL 		004
----- A 121 030 12 17  PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE NÜRAL FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL 		004
----- A 001 037 42 16  COMPRESSION RING
FOR GROOVE I 		004
----- A 001 037 47 16  TAPERED RING
FOR GROOVE II 		004
----- A 000 037 03 17  NOVIX STEPPED RING
FOR GROOVE III 		004
----- A 000 037 38 18  NOVIX SLOTTED RING
FOR GROOVE IV 		004
----- PISTON PIN
D 25 X 18 X 72 DIN 73121 K 		004
----- WIRE SNAP RING
A 25 DIN 73123 		008