ELECTRICAL EQUIPMENT AT ENGINE [Car] MERCEDES [EUROPA] [CHASSIS]TYP 180


ELECTRICAL EQUIPMENT AT ENGINE [Car] MERCEDES [EUROPA] [CHASSIS]TYP 180122121117118566266656457636159114a6869675872715577781041051061141131091071087091908994838481828586877475737676a9762898808882a127126116115120124125121123119128404149481514171319201821222381a1011021002425262629304239434347465417163910121131343332333435363738
Item no. Part number Designation/description Quant information
STARTER MOTOR
1 A 000 151 77 01  STARTER MOTOR
WITH PUSH BUTTON OPERATION 		001
----- A 000 151 83 01  STARTER MOTOR
WITH PUSH BUTTON OPERATION 		001
2 A 000 151 20 13  ROLLER FREEWHEEL 001
3 A 000 152 10 11  SOLENOID SWITCH 001
4 A 000 151 14 14  SET OF CARBON BRUSHES
4 PIECES 		001
5 A 000 151 05 93  PRESSURE SPRING
FOR CARBON BRUSH 		004
6 A 000 151 07 50  BEARING BUSHING
IN DRIVE BEARING 		001
7 A 000 151 08 50  BEARING BUSHING
IN COMMUTATOR BEARING 		001
8 A 120 151 00 12  INTERMEDIATE FLANGE
FOR STARTER MOTOR AT CLUTCH HOUSING 		001
9 HEX.-HD. SCREW
M 12X80 DIN 931-8 G FOR STARTER MOTOR AT CLUTCH HOUSING 		002
10 WASHER
13 DIN 433 FOR STARTER MOTOR AT CLUTCH HOUSING 		002
11 LOCK WASHER
B 12 DIN 127 FOR STARTER MOTOR AT CLUTCH HOUSING 		002
12 HEX. NUT
M 12 DIN 934-5 S FOR STARTER MOTOR AT CLUTCH HOUSING 		002
GENERATOR
13 A 000 154 48 02  GENERATOR 160 WATT 001
14 A 000 154 27 14  SET OF CARBON BRUSHES
2 PIECES 		001
15 A 000 154 06 93  PRESSURE SPRING
FOR CARBON BRUSH 		002
16 A 000 154 55 06  THREE-ELEMENT VOLTAGE
REGULATOR SEE ALSO GROUP 54 		001
17 A 180 155 07 15  PULLEY
FOR GENERATOR OPTIONAL 		001
----- A 180 155 08 15  PULLEY
FOR GENERATOR OPTIONAL 		001
18 WOODRUFF KEY
3X5 DIN 6888 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
19 LOCK WASHER
B 12 DIN 127 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
20 HEX. NUT
M 12 X 1,5 DIN 936-5 S FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
21 A 121 155 08 35  SUPPORT
FOR GENERATOR 		001
----- A 121 155 03 35  SUPPORT
FOR GENERATOR 		001
22 LOCK WASHER
B 10 DIN 127 FOR CYLINDER CRANKCASE 		002
23 HEX. NUT
M 10 DIN 934-5S FOR CYLINDER CRANKCASE 		002
24 A 121 150 03 32  GROUND CABLE
FOR SUPPORT AT GENERATOR 		001
25 HEX.-HD. SCREW
M 8 X 35 DIN 931-8 G FOR GENERATOR AT SUPPORT 		001
----- HEX.-HD. SCREW
M 8 X 40 DIN 931-8 G FOR GENERATOR AT SUPPORT 		002
26 A 121 155 00 76  INTERMEDIATE WASHER
FOR GENERATOR AT SUPPORT 		002
----- A 121 991 04 40  SLEEVE
FOR GENERATOR AT SUPPORT, FRONT 		001
----- A 121 155 00 81  RUBBER PLATE
FOR GENERATOR AT SUPPORT, FRONT 		002
----- A 121 155 00 82  WASHER
FOR GENERATOR AT SUPPORT, FRONT 		002
----- A 121 155 01 76  INTERMEDIATE WASHER
FOR GENERATOR AT SUPPORT, REAR 		002
29 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT SUPPORT 		001
30 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT SUPPORT 		001
31 HEX.-HD.SCREW
M 8X60 DIN 931-8 G FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
32 A 180 991 06 40  SLEEVE
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
33 A 120 155 00 81  RUBBER PLATE
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002
34 A 120 155 00 82  WASHER
FOR GENERATOR SUSPENSION, RUBBER MOUNTED FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002
35 A 121 990 01 40  WASHER
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
36 A 121 155 00 53  SPACER SLEEVE,
25.5-MM LONG FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
37 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
38 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
39 A 121 155 01 23  TIGHTENING SCREW
FOR GENERATOR ADJUSTMENT 		001
40 A 121 155 00 72  TIGHTENING NUT
FOR GENERATOR ADJUSTMENT 		001
41 A 121 155 01 28  CLAMPING PIECE
FOR GENERATOR ADJUSTMENT 		001
42 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR ADJUSTMENT 		001
43 A 121 155 00 76  INTERMEDIATE WASHER
FOR TIGHTENING SCREW WITH CLAMPING PIECE AT CYLINDER CRANKCASE 		002
46 LOCK WASHER
B 8 DIN 127 FOR TIGHTENING SCREW WITH CLAMPING PIECE AT CYLINDER CRANKCASE 		001
47 HEX. NUT
M 8 DIN 934-5 S FOR TIGHTENING SCREW WITH CLAMPING PIECE AT CYLINDER CRANKCASE 		001
48 HEX. HEAD SCREW
M 8X30 DIN 931-8 G FOR CLAMPING PIECE AT GENERATOR 		001
49 LOCK WASHER
B 8 DIN 127 FOR CLAMPING PIECE AT GENERATOR 		001
----- A 121 155 02 23  TIGHTENING SCREW
FOR GENERATOR ADJUSTMENT 		001
----- HEX. HEAD SCREW
M 8X60 DIN 931-8 G FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		001
----- A 121 155 00 51  SPACER RING
FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		001
----- A 121 155 01 76  INTERMEDIATE WASHER
FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		002
IGNITION DISTRIBUTOR
----- A 000 158 51 01  REPLACED BY
000 158 73 01 TOGETHER WITH 1 VACUUM PIPE 121 150 05 35 UP TO ENGINE 9501281
----- A 000 158 70 01  REPLACED BY
000 158 73 01 TOGETHER WITH 1 VACUUM PIPE 121 150 05 35 UP TO ENGINE 9501281
55 A 000 158 73 01  IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM CONTROL INTERFERENCE SUPRESSION FROM ENGINE 9501282 		001
----- A 000 158 64 01  REPLACED BY
000 158 74 01 TOGETHER WITH 1 VACUUM PIPE 121 150 05 35 UP TO ENGINE 9501281 EXPORT, SPECIAL REQUEST WITH INTERFERENCE S
----- A 000 158 74 01  IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM CONTROL FROM ENGINE 9501282 EXPORT, SPECIAL REQUEST WITH INTERFERENCE SUPPRESSION AND DUST PROT 		001
56 A 000 158 06 02  DISTRIBUTOR PLATE
WITH CARBON BRUSH 		001
57 A 000 158 00 34  CARBON BRUSH WITH SPRING 001
58 A 000 158 04 89  OILER IN HOUSING 001
59 A 000 158 07 90  CONTACT SET 001
----- A 000 158 06 31 

Replaced by: A 000 158 15 31
----- A 000 158 05 31 

Replaced by: A 000 158 15 31
----- A 000 158 11 31  DISTRIBUTOR ROTOR
WITH COUNTER WEIGHT DUST-PROOF AND INTERFERENCE SUPPRESSED

Replaced by: A 000 158 15 31
61 A 000 158 15 31  DISTRIBUTOR ROTOR
WITH COUNTER WEIGHT DUST-PROOF AND INTERFERENCE SUPPRESSED 		001
----- A 000 158 00 11  DUST PROTECTION COVER
EXPORT, SPECIAL REQUEST 		001
62 A 000 158 03 33  LEAF SPRING
FOR DISTRIBUTOR PLATE 		002
63 A 000 158 03 40  FIXING PLATE WITHOUT NOSE 001
64 A 000 158 04 40  FIXING PLATE WITH NOSE 001
65 CYLINDER SCREW
AM 4X8 DIN 84 - 4 S FOR FIXING PLATE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002
66 LOCK WASHER
B 4 DIN 127 FOR FIXING PLATE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002
----- A 000 156 11 01  CONDENSER AT HOUSING
UP TO ENGINE 9501281 		001
67 A 000 156 49 01  CONDENSER AT HOUSING
FROM ENGINE 9501282 		001
68 CYLINDER SCREW
AM 4X5 DIN 84-5 S FOR CONDENSER AT IGNITION DISTRIBUTOR 		002
69 LOCK WASHER
B 4 DIN 127 FOR CONDENSER AT IGNITION DISTRIBUTOR 		002
----- A 000 158 04 18  VACUUM CONTROL
UP TO ENGINE 9501281 		001
70 A 000 158 05 18  VACUUM CONTROL
FROM ENGINE 9501282 		001
71 CYLINDER SCREW
AM 4X5 DIN 84-5 S FOR VACUUM CONTROL AT IGNITION DISTRIBUTOR 		002
72 LOCK WASHER
B 4 DIN 127 FOR VACUUM CONTROL AT IGNITION DISTRIBUTOR 		002
----- A 000 158 03 09  COUPLING
ON SHAFT UP TO ENGINE 9501281 		001
73 A 000 158 05 09  COUPLING
ON SHAFT FROM ENGINE 9501282 		001
74 A 000 158 01 76  FIBER WASHER
FOR COUPLING AT IGNITION DISTRIBUTOR 		002
75 A 000 158 00 52  SHIM 0.1 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB
----- A 000 158 04 52  SHIM 0.1 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB
----- A 000 158 04 74  PIN
FOR COUPLING AT IGNITION DISTRIBUTOR UP TO ENGINE 9501281 		001
76 A 000 158 07 74  PIN
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501282 		001
76a A 000 158 02 77  SNAP RING
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501282 		001
77 A 000 158 00 59  THREADED BUSHING 001
78 A 000 158 02 60  SEALING RING 001
----- A 121 150 01 07  BEARING, IGNITION

Replaced by: A 121 150 02 07
80 A 121 150 02 07  BEARING, IGNITION 001
81 A 180 150 01 24  ADJUSTING LEVER
WITH ANGLE UP TO ENGINE 8510256 		001
81a A 180 150 03 24  ADJUSTING LEVER
FROM ENGINE 8510257 		001
82 HEX. -HD. SOCKET SCREW
M 6X25 DIN 912-8 G 		001
82a A 180 150 02 24  ADJUSTING ECCENTRIC
FROM ENGINE 8510257 		001
----- SPRING WASHER
B 6 DIN 137 FOR ADJUSTING LEVER AT ADJUSTING ECCENTRIC FROM ENGINE 8510257 		001
----- HEX.-HD.SCREW
M 6X18 DIN 933-8 G FOR ADJUSTING LEVER AT ADJUSTING ECCENTRIC FROM ENGINE 8510257 		001
83 HEX.-HD.SCREW
M 5X30 S DIN 931-8 G FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
84 WASHER
5,3 DIN 125 FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
85 A 136 993 08 01  HELICAL SPRING
FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
86 HEX. NUT
M 5 DIN 934-5 S FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
87 COTTER PIN
1X12 DIN 94 FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
88 HEX. -HD.
SCREW WITH PIVOT AM 6 X 12 DIN 561 - 5 S FOR FIXING OF IGNITION DISTRIBUTOR UP TO ENGINE 8510256 		001
89 A 186 993 24 01  PRESSURE SPRING
FOR IGNITION TIMING UP TO ENGINE 8510256 		001
90 A 121 150 00 84  ADJUSTING SCREW
FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8510256 		001
91 A 121 990 00 57  KNURLED NUT
FOR ADJUSTING SCREW UP TO ENGINE 8510256 		001
94 A 121 158 00 76  WASHER
FOR ADJUSTING SCREW UP TO ENGINE 8510256 		001
97 A 180 150 01 07  BEARING WITH BUSHING
FOR IGNITION DISTRIBUTOR AND OIL PUMP HOUSING 		001
98 A 180 158 04 12  HELICAL GEAR
FOR IGNITION DISTRIBUTOR DRIVE 		001
100 A 121 158 00 51  INTERMEDIATE RING
FOR BEARING, IGNITION DISTRIBUTOR AT CYLINDER CRANKCASE 		001
101 HEX.-HD.SOCKET SCREW
M 8X45 DIN 912-8 G FOR BEARING, IGNITION DISTRIBUTOR AT CYLINDER CRANKCASE 		001
102 WASHER
8,4 DIN 125 FOR BEARING, IGNITION DISTRIBUTOR AT CYLINDER CRANKCASE 		001
----- A 121 150 02 35  VACUUM PIPE
UP TO ENGINE 9501281 		001
104 A 121 150 05 35  VACUUM PIPE
FROM ENGINE 9501282 		001
----- REPLACED BY 4 DIN 3871
4,2 DIN 71426
105 CONNECTING SCREW
4 DIN 3871 		001
----- REPLACED BY 4 DIN 3862
4,1 DIN 71426
106 DOUBLE CONE RING
4 DIN 3862 		001
107 A 181 997 03 82  RUBBER HOSE 001
108 A 181 997 00 90  HOSE STRAP 002
----- A 180 995 04 01  SPRING CLAMP
FOR FUEL LINE AND VACUUM PIPE

Replaced by: A 180 993 05 25
109 A 180 993 05 25  SPRING CLAMP
FOR FUEL LINE AND VACUUM PIPE 		002
----- HEX.-HD.SCREW
M 5X10 DIN 933-8 G FOR FUEL LINE AND VACUUM PIPE UP TO ENGINE 7504195 		002
----- LOCK WASHER
B 5 DIN 127 FOR FUEL LINE AND VACUUM PIPE UP TO ENGINE 7504195 		002
----- HEX. NUT
M 5 DIN 934-5 S FOR FUEL LINE AND VACUUM PIPE UP TO ENGINE 7504195 		002
113 SEALING RING
A 6X12 DIN 7603 A1 FOR VACUUM CONNECTION AT CARBURETOR 		001
114 A 181 158 01 37  CONNECTION FITTING
FOR VACUUM CONNECTION AT CARBURETOR 		001
114a A 121 150 02 32  GROUND CABLE
FROM IGNITION DISTRIBUTOR TO CYLINDER HEAD 		001
IGNITION CABLE
----- A 121 150 01 19  IGNITION CABLE
HARNESS WITH PROTECTIVE TUBE

Replaced by: A 121 150 03 19
115 A 121 150 03 19  IGNITION CABLE
HARNESS WITH PROTECTIVE TUBE 		001
----- REPLACED BY
000 156 15 10 OR 000 156 16 10, RESPECTIVELY C DIN 72566
116 A 000 156 15 10  IGNITION CABLE
PLUG WITH INTERFERENCE SUPPRESSION OPTIONAL 		004
----- A 000 156 16 10  IGNITION CABLE
PLUG WITH INTERFERENCE SUPPRESSION OPTIONAL 		004
117 A 000 159 00 38  CABLE SLEEVE 004
----- A 000 156 10 10  REPLACED BY
000 156 17 10 OR 000 156 18 10, RESPECTIVELY
----- A 000 156 17 10  PLUG FOR
INTERFERENCE SUPPRESSION OPTIONAL FOR IGNITION DISTRIBUTOR SPECIAL REQUEST - FOR RADIO INSTALLATION 		004
----- A 000 156 18 10  PLUG FOR
INTERFERENCE SUPPRESSION OPTIONAL FOR IGNITION DISTRIBUTOR SPECIAL REQUEST - FOR RADIO INSTALLATION 		004
118 A 000 159 00 85  RAIN PROTECTIVE CAP
FOR IGNITION DISTRIBUTOR 		004
----- A 000 159 05 85  RUBBER CAP
FOR IGNITION DISTRIBUTOR

Replaced by: A 000 159 07 85
----- A 000 159 07 85  RUBBER CAP
FOR IGNITION DISTRIBUTOR SPECIAL REQUEST (FOR RADIO INSTALLATION) 		004
119 A 000 997 22 81  GROMMET
FOR PROTECTIVE TUBE 		004
120 A 180 150 06 18  IGNITION
FOR IGNITION COIL, DISTRIBUTOR 		001
----- A 000 159 00 38  CABLE SLEEVE 002
----- A 000 156 10 10  REPLACED BY
000 156 17 10 OR 000 156 18 10, RESPECTIVELY
----- A 000 156 17 10  PLUG FOR
INTERFERENCE SUPPRESSION OPTIONAL FOR IGNITION DISTRIBUTOR SPECIAL REQUEST - (FOR RADIO INSTALLATION) 		001
----- A 000 156 18 10  PLUG FOR
INTERFERENCE SUPPRESSION OPTIONAL FOR IGNITION DISTRIBUTOR SPECIAL REQUEST - (FOR RADIO INSTALLATION) 		001
----- A 000 159 00 85  RAIN PROTECTIVE CAP
FOR IGNITION CABLE 		002
----- A 000 159 05 85  RUBBER CAP
FOR IGNITION CABLE

Replaced by: A 000 159 07 85
----- A 000 159 07 85  RUBBER CAP
FOR IGNITION CABLE SPECIAL REQUEST (FOR RADIO INSTALLATION) 		001
121 A 159 546 00 37  GROMMET 002
122 CABLE TERMINAL
4 X 0,8 N 261 		001
123 CABLE TERMINAL
5 X 0,8 N 261 		001
124 LOCK WASHER
B 6 DIN 127 FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002
125 HEX.-HD.SCREW
M 6X10 DIN 933-8 G FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002
SPARK PLUG
----- A 000 159 46 03  SPARK PLUG
MAKE BOSCH OPTIONAL

Replaced by: A 000 159 59 03
126 A 000 159 59 03  SPARK PLUG
MAKE BOSCH OPTIONAL 		004
----- A 000 159 06 03  SPARK PLUG
OPTIONAL

Replaced by: A 000 159 75 03
----- A 000 159 75 03  SPARK PLUG
MAKE BERU OPTIONAL 		004
----- A 000 159 55 03  SPARK PLUG,
INTERFERENCE-FREE MAKE BOSCH OPTIONAL SPECIAL REQUEST FOR RADIO INSTALLATION 		004
----- A 000 159 45 03  SPARK PLUG,
INTERFERENCE-FREE OPTIONAL SPECIAL REQUEST FOR RADIO INSTALLATION

Replaced by: A 000 159 78 03
----- A 000 159 78 03  SPARK PLUG,
INTERFERENCE-FREE MAKE BERU OPTIONAL SPECIAL REQUEST FOR RADIO INSTALLATION 		004
127 SEALING RING
C 14 X 20 DIN 7603 ST. ASB. FOR SPARK PLUG AT CYLINDER HEAD HAS TO BE DELIVERED WITH SPARK PLUG 		004
IGNITION COIL
128 A 000 158 00 03  IGNITION COIL
AT FRONT WALL SEE GROUP 54 		001