| Item no. |
Part number |
Designation/description |
Quant |
information |
|
CRANKSHAFT
|
|
----- |
A 121 030 53 01 |
CRANKSHAFT WITH
FLYWHEEL, COLLAR SCREW, CRANKSHAFT BEARING AND CONNECTING ROD BEARING SHELLS, MAKE LAUCHERTAL OPTIONAL |
001 |
|
|
----- |
A 121 030 54 01 |
CRANKSHAFT WITH
FLYWHEEL, COLLAR SCREW, CRANKSHAFT BEARING AND CONNECTION ROD BEARING SHELLS, MAKE GLYCO OPTIONAL |
001 |
|
|
----- |
A 121 030 55 01 |
CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL
Replaced by: A 121 030 35 01 |
|
|
|
1 |
A 121 030 35 01 |
CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL |
001 |
|
|
2 |
A 180 031 00 52 |
SPACER RING,
5.45-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 |
|
|
----- |
A 180 031 01 52 |
SPACER RING,
5.60-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 |
|
|
----- |
A 180 031 02 52 |
SPACER RING,
5.75-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 |
|
|
----- |
A 180 031 03 52 |
SPACER RING,
5.90-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 |
|
|
----- |
A 180 031 04 52 |
SPACER RING,
6.05-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 |
|
|
3 |
|
WOODRUFF KEY
5X7,5 DIN 6888 |
001 |
|
|
----- |
A 122 052 01 03 |
CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT
Replaced by: A 180 052 02 03 |
|
|
|
4 |
A 180 052 02 03 |
CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT |
001 |
|
|
5 |
A 180 031 04 25 |
OIL SLINGER RING
ON CRANKSHAFT, FRONT |
001 |
|
|
5a |
A 121 031 03 07 |
COUNTERWEIGHT |
001 |
|
|
5b |
A 121 031 00 51 |
SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING |
001 |
|
|
6 |
|
CYLINDRICAL PIN
8 H 8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 |
|
|
7 |
|
CYLINDRICAL PIN
8 H 8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 |
|
|
8 |
A 121 030 08 05 |
FLYWHEEL WITH RING GEAR |
001 |
|
|
9 |
A 121 032 00 05 |
STARTER RING
GEAR, 108 TEETH |
001 |
|
|
10 |
A 121 031 06 71 |
EXPANDING SCREW
FOR FLYWHEEL AT CRANKSHAFT |
006 |
|
|
11 |
|
CYLINDRICAL PIN
10 H 8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT |
001 |
|
|
13 |
A 186 031 02 71 |
COLLAR SCREW |
001 |
|
|
14 |
A 120 031 01 81 |
SEALING RING
AT CRANKSHAFT, FRONT |
001 |
|
|
14a |
A 121 032 00 15 |
ADJUSTING NEEDLE
FOR ADJUSTING TOP DEAD CENTER |
001 |
|
|
----- |
|
CYLINDRICAL SCREW
AM 6X8 DIN 84-4 S FOR FIXING OF ADJUSTING NEEDLE FROM ENGINE 8507471 |
001 |
|
|
15 |
A 121 200 01 05 |
PULLEY |
001 |
|
|
16 |
|
ANNULAR GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT |
001 |
|
|
17 |
A 186 031 00 33 |
LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT |
001 |
|
|
18 |
|
SEALING RING, FABRIC
75X87X6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR |
001 |
|
|
CRANKSHAFT BEARING
|
|
20 |
A 121 030 05 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. = 70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 621 030 00 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 030 10 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 |
|
|
21 |
A 121 033 14 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 621 033 00 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 19 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
22 |
A 121 033 14 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 621 033 00 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 033 19 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 030 06 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 621 030 01 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 030 11 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 033 15 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 621 033 01 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 20 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 15 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 621 033 01 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 033 20 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 030 07 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM = REP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 621 030 02 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM=REP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 030 12 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM = RP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 033 16 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 621 033 02 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 21 02 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 16 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 621 033 02 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 033 21 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 030 08 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM=REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 621 030 03 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM =REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 030 13 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM=REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 033 17 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 621 033 03 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 22 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 17 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 621 033 03 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 033 22 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 030 09 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.00-MM=REP.SIZE IV READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 621 030 04 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MM=REP. SIZE IV READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 030 14 97 |
SET OF
CRANKSHAFT BEARING SHELLS, INNER DIA. =69.00-MM =REP.SIZE IV READY FOR INSTALLATION OPTIONAL |
001 |
|
|
----- |
A 121 033 18 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 621 033 04 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 23 01 |
CRANKSHAFT BEARING SHELL
WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 |
|
|
----- |
A 121 033 18 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 621 033 04 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
----- |
A 121 033 23 02 |
CRANKSHAFT BEARING SHELL
WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 |
|
|
CONNECTING ROD
|
|
25 |
A 121 030 15 20 |
CONNECTING ROD |
004 |
|
|
26 |
A 186 038 07 50 |
CONNECTING BUSHING |
004 |
|
|
27 |
A 121 038 03 71 |
CONNECTING SCREW |
008 |
|
|
28 |
A 182 038 00 72 |
NUT |
008 |
|
|
----- |
A 186 038 08 50 |
CONNECTING BUSHING,
OUTER DIA. = 28.5-MM REPAIRS |
004 |
|
|
----- |
A 121 038 28 11 |
CONNECTING ROD
BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 28 10 |
|
|
|
29 |
A 121 038 28 10 |
CONNECTING ROD
BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 07 11 |
CONNECTING ROD
BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 07 10 |
|
|
|
----- |
A 121 038 07 10 |
CONNECTING ROD
BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 33 10 |
CONNECTING ROD
BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 29 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 29 10 |
|
|
|
----- |
A 121 038 29 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZ E I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 08 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZ E I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 08 10 |
|
|
|
----- |
A 121 038 08 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 34 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 30 11 |
CONNECTING ROD
BEARING SHELL, REPAIR SIZE II, INNER DIA. 51.50-MM
Replaced by: A 121 038 30 10 |
|
|
|
----- |
A 121 038 30 10 |
CONNECTING ROD
BEARING SHELL, REPAIR SIZE II, INNER DIA. 51.50-MM OPTIONAL WITH 121 038 09 10/35 10 |
008 |
|
|
----- |
A 121 038 09 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10
Replaced by: A 121 038 09 10 |
|
|
|
----- |
A 121 038 09 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10 |
008 |
|
|
----- |
A 121 038 35 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10 |
008 |
|
|
----- |
A 121 038 31 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION
Replaced by: A 121 038 31 10 |
|
|
|
----- |
A 121 038 31 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 10 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 10 10 |
|
|
|
----- |
A 121 038 10 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 36 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 32 11 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION
Replaced by: A 121 038 32 10 |
|
|
|
----- |
A 121 038 32 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 11 11 |
CONNECTING ROD BEARING
REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL
Replaced by: A 121 038 11 10 |
|
|
|
----- |
A 121 038 11 10 |
CONNECTING ROD BEARING
REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
----- |
A 121 038 37 10 |
CONNECTING ROD
BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 |
|
|
PISTONS
|
|
34 |
A 121 030 18 17 |
PISTON WITH
PIN AND RINGS, CYLINDER DIA. 85.00-MM = STANDARD |
004 |
|
|
35 |
A 001 037 38 16 |
COMPRESSION RING
PISTON GROOVE I |
004 |
|
|
36 |
A 001 037 43 16 |
TAPERED COMPRESSION
PISTON RING PISTON GROOVE II |
004 |
|
|
37 |
A 000 037 00 17 |
NOVIX STEPPED RING
PISTON GROOVE III |
004 |
|
|
38 |
A 000 037 29 18 |
NOVIX-SLOTTED RING
PISTON GROOVE IV |
004 |
|
|
----- |
A 121 037 00 20 |
REPLACED BY
D 25X18X72 DIN 73121 K |
|
|
|
39 |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
004 |
|
|
40 |
|
WIRE SNAP RING
A 25 DIN 73123 |
008 |
|
|
----- |
A 121 030 03 17 |
PISTON WITH
PIN AND RINGS, CYLINDER DIA. 85.25-MM = REP. SIZE I |
004 |
|
|
----- |
A 001 037 39 16 |
COMPRESSION RING
PISTON GROOVE I |
004 |
|
|
----- |
A 001 037 44 16 |
TAPERED COMPRESSION
PISTON RING PISTON GROOVE II |
004 |
|
|
----- |
A 000 037 11 17 |
NOVIX STEPPED RING
PISTON GROOVE III |
004 |
|
|
----- |
A 000 037 69 18 |
NOVIX SLOTTED RING
PISTON GROOVE IV |
004 |
|
|
----- |
|
PISTON RING
D 25 X 18 X 72 DIN 73121-K |
004 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
008 |
|
|
----- |
A 121 030 04 17 |
PISTON WITH
PIN AND RINGS, CYLINDER DIA. 85.50-MM = REP. SIZE II |
004 |
|
|
----- |
A 001 037 40 16 |
COMPRESSION RING
PISTON GROOVE I |
004 |
|
|
----- |
A 001 037 45 16 |
TAPERED COMPRESSION
PISTON RING PISTON GROOVE II |
004 |
|
|
----- |
A 000 037 01 17 |
NOVIX STEPPED RING
PISTON GROOVE III |
004 |
|
|
----- |
A 000 037 36 18 |
NOVIX SLOTTED RING
PISTON GROOVE IV |
004 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 - K |
004 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
008 |
|
|
----- |
A 121 030 05 17 |
PISTON WITH
PIN AND RINGS, CYLINDER DIA. 86.00-MM = REP. SIZE III |
004 |
|
|
----- |
A 001 037 41 16 |
COMPRESSION RING
PISTON GROOVE I |
004 |
|
|
----- |
A 001 037 46 16 |
TAPERED COMPRESSION
PISTON RING PISTON GROOVE II |
004 |
|
|
----- |
A 000 037 02 17 |
NOVIX STEPPED RING
PISTON GROOVE III |
004 |
|
|
----- |
A 000 037 37 18 |
NOVIX SLOTTED RING
PISTON GROOVE IV |
004 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 - K |
004 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
008 |
|
|
----- |
A 121 030 06 17 |
PISTON WITH
PIN AND RINGS, CYLINDER DIA. 86.5-MM = REP. SIZE IV |
004 |
|
|
----- |
A 001 037 42 16 |
COMPRESSION RING
PISTON GROOVE I |
004 |
|
|
----- |
A 001 037 47 16 |
TAPERED COMPRESSION
PISTON RING PISTON GROOVE II |
004 |
|
|
----- |
A 000 037 03 17 |
NOVIX STEPPED RING
PISTON GROOVE III |
004 |
|
|
----- |
A 000 037 38 18 |
NOVIX SLOTTED RING
PISTON GROOVE IV |
004 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 -K |
004 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
008 |
|
![MOVING PARTS [Car] MERCEDES [EUROPA] [CHASSIS]TYP 180](https://img.7zap.com/images/oem/mercedes/Imgs/BM_IMAGES_ARC/B03003Z09001.051209.png)